Dual Position Car Seat Headrest Tablet Mount with Table Tray (HRMOUNTPROTRAY)

MPN#: HRMOUNTPROTRAY
Type: Car & Truck Accessories


The Macally HRMOUNTPROTRAY dual position car seat headrest tablet mount allows passengers to comfortably eat while watching movies on their tablet from the back seat of the car.

The headrest mount can be easily and securely attached to the car's front seat headrest posts with a width of 2” to 7¼”.  The cradle fits any tablet and mobile device with a width of 4.5” to 10”.

The strong aluminum frame can be extended so that the holder can be placed in the center (between the two front seats) so that all passengers can enjoy the same movie, at the same time. The cradle is fully adjustable and can rotate between portrait and landscape view.

The large 12.40" wide fold down table has a 3" wide cup holder (2.5" deep) and a raised lip to securely keep drinks and food in place while on the road.

 

FEATURES:

  • Adjustable grip fits iPad, iPhone, tablet, Smartphone and any mobile device (with/without protective case) between 4.25” and 9.25” either long or wide
  • Supports headrest posts between 2" and 7¼”
  • Strong aluminum shaft can be extended to place the holder between the two front seats
  • Soft holder grip to protect your iPad/iPhone/tablet/Smartphone from scratching
  • Arm grip release button for an easy removal of your  iPad/iPhone/tablet/Smartphone
  • Adjustable so that the back seat user can keep the tray leveled at all times.  Even with slightly reclined driver/passenger seats. 
  • Easily folds upward and locks into place to keep the tray out of the way when not in use. 
  • 12.40" (31.5 cm) x 5.6" (14.2 cm) wide table tray with a raised lip and a 3"/7.6 cm wide cup holder (2.5"/6.3 cm deep) to securely keep drinks and food in place

BENEFITS:

  • Mounts your iPad/tablet and Smartphone securely to the car's headrest
  • Supports headrest posts between 2" and 7.2" wide
  • Strong aluminum shaft can be extended to place cradle holder between the two front seats
  • Swivel ball-head to accommodate optimal viewing angles
  • Cradle fits iPad/tablet and any other mobile device between 4.25” and 9.25” either long or wide.
  • Soft grip pad and back support to protect your iPad/tablet from scratching.
  • Quick rotation between portrait and landscape view
  • Quick installation and dismounting, no tools required.
  • Helps keep your automobile clean and organized.  Holds up to 5lbs.
  • Multifunctional and easy to use.
  • Securely keeps your passengers drink and food in place while on the road. 
  • Easy to adjust so that the back seat user can keep the tray leveled while the front seat user has his/hers seat reclined. 

SET UP/INSTALLATION:

NOTE: The HRMOUNTPROTRAY is shipped so that it can be mounted on the back "passenger side" seat (extension arm pulling out from the left side). Please refer to the "Driver side seat mounting" section of this user's guide for steps on how to flip the table tray.


1. Loosen the head post clamps, place the clamps onto the headrest posts and then firmly tighten them into place by turning the clamp knobs.

2. Pull the tray downward and make adjustments to the tray angle by loosening and tightening the tray angle adjustment knob  as needed.

3. Attach the Smartphone/tablet cradle on to the cradle holder and then pull the cradle holder upward until it clicks securely into place.

4. Slide the cradle holder onto the mount until it clicks securely into place.
NOTE: You can place the holder either behind the seat or at the end of the aluminum frame so that the Smartphone/tablet is centered between the driver and passenger seats.

5. Push in the two arm-grip release buttons while pulling up on the top arm grip. Only pull out the top arm grip until the opening width between the top and bottom arm grips is about ½” shorter than the width or length of your tablet or phone to be held. You will use the spring-loaded arm grip as the main grip to securely hold your device into place.   Slide out the bottom arm grips for tablet.

6. Place your Smartphone/tablet onto the bottom arm grips, and pull the spring-loaded arm rip upward (you will feel the spring) to hold your tablet or phone securely.

DRIVER SIDE SEAT MOUNTING

These steps will guide you on how to flip the tray so that it can be mounted on the back of the driver side seat (extension arm pulling out from the right side).  Once completed please refer to step one of the "How to use the HRMOUNTPROTRAY" section of this users guide. 

1. Completely un-loosen the tray angle adjustment knob assembly and detach the tray from the HRMOUNTPRO.

2.  Re-attach the tray so that the extension arm pulls out from the right side and screw it back into place using the  angle adjustment knob. 

 

 


Related Items